|
Allendale Electronics Ltd. Unit 43 Hoddesdon Industrial Centre, Pindar Road, Hoddesdon, Hertfordshire, EN11 0FF Suppliers of Tapping Equipment... UK PowerSeller w VAT Registered w Next Day Delivery w UK Technical Support w Import Duty Already Paid w 1 Year Warranty w UK Showroom in Hoddesdon, Hertfordshire w Detailed User Manual w Spares available Pantographic tapping arm with pneumatic motor... You are purchasing the following: - 1 off Reversible pneumatic motor. 1 off M3, M4, M5, M6, M8, M10 and M12 tap collets. 1 off Air regulator, filter and lubricator. 1 year Warranty - more details Our Pantographic tapping arm will tap from M3 to M10 in mild steel and M3 to M12 in aluminium. The taps are held in a quick change collet system driven by a pneumatic motor. The motor is mounted on a articulated arm which maintains parallel motion. The smooth arm action allows the tap to be brought into Setting and Operating the pneumatic motor... The pneumatic motor can be set at any angle between the vertical and horizontal position. The motor has a locating peg for the vertical position and is secured by a threaded locking handle. To adjust the angle simply loosen the locking handle, swivel to desired angle and tighten locking handle. The pneumatic motor on the pantographic arm has a gas strut counter balance, making for light operation and reduced operator fatigue. The pneumatic motor has a large finger operated paddle trigger and thumb operated reverse button. Pull the trigger to start forward rotation, hold both paddle trigger and reverse button for reverse rotation. The pneumatic motor is equipped with a chuck and each tap is held in its own collet. To change to a different tap size, lift the locking ring on the chuck. This will eject the collet from the motor. Select the collet with the desired tap size. Insert the collet into the chuck. Locate the two drive pegs on the collet and release the locking ring to secure. Each collet has a ratchet clutch, the torque is preset for each size of tap preventing tap breakage. The clutch system will allow blind holes as well as through holes to be tapped. The torque clutch allows the tap to stop turning when it encounters any obstruction that may cause tap breakage. M3 to M6 collets use standard ISO 529 machine taps. M8 to M12 collets use long shank ISO 2283 or BS949 machine taps. (NOTE: Machine taps not supplied with tapping arm) The tapping arm has a working area of 180mm from its base and 900mm overall reach. The tapping arm can rotate 360˚ around its mounting base. Which has four 9mm diameter mounting holes, to secure the arm to a bench or a machine table. The long reach of the tapping arm allows large fabrications/components to remain stationary when being tapped. With the increase in speed over hand tapping and removing tapping operations from manual and cnc machinery, our tapping arm will prove to be an affordable alternative. capable of many other common operations including chamfering/deburring, helicoil insertion and screw/nut driving. Please contact us for more details. Allendale Electronics Ltd guarantee all products for one year from date of purchase. During this period Allendale Electronics Ltd will repair or replace all defective products free of charge (return to base warranty), except for units subject to fair wear and tear. To qualify for benefits under the guarantee you must have installed and used the product in accordance with Allendale Electronics Ltd instructions or user manual. Consequential losses and accidental damage to the product are not covered by the guarantee. Allendale Electronics Ltd cannot be responsible for results of using our products for any purposes other than those described in the relevant instructions or user manual. Please make cheques/postal orders payable to Allendale Electronics Ltd and post to Allendale Electronics Ltd. 43 Hoddesdon Industrial Centre, Pindar Road, Hoddesdon, Herts. EN11 0FF Orders may be collected from our factory/showroom in Hoddesdon, Hertfordshire. VAT receipt included with despatch. Unit 43 Hoddesdon Industrial Centre Machine-tapping (Division of Allendale Electronics Ltd) was originally founded in Harlow, Essex. In April 2006 we expanded into larger premises in Hoddesdon Industrial Centre. We now have an engineering tool room which has our exhibition machinery on display. As our tool room is in constant use, we would ask that you contact us first before visiting. Thank you for looking at our items... © Copyright 2007 - All rights reserved - Allendale Electronics Ltd (Pantographic tapping arm & pneumatic motor quick collet is the responsibility of Colette Gregory) |
Colette-gregory@cedar--rapids.com (Colette Gregory) for more information.
