"Your One Stop Source for Sales & Calibration of Test & Measurement Equipiment" * Kenwood CS-4125A 20 MHz Oscilloscope* The CS-4100A Series with excellent cost efficiency were created from a fusion of performance, reliability, operability and design, and realize general-purpose characteristics which can be used in a variety of observations and inspections ranging from very small to very large signals. * High sensitivity of 1 mV/div (DC to 5 MHz) * Vertical axis signal output connector * Maximum sweep rate of 20 ns/div (x10 MAG) * Dynamic range with a headroom for accurate waveform display without distortion * Waveforms can be observed by applying intensity modulation. * Added or subtracted waveforms can be observed. * High-intensity CRT (12 kV) (with scale illumination) * High reliability with Kenwood Original Hibrid ICs * One-touch ALT/CHOP switching * Relay-type attenuators with long life and excellent operability are used. * The trace inclination can be corrected with the front panel operation. 150mm rectangular with internal graticule 1mV/div to 5V/div (1mV/div., 2mV/div+5%, 5mV/div to 5V/div. +3% 1-2-5 steps, 12 ranges, and fine adjustment Vertical axis frequency response DC DC to 40MHz(-3dB) (5mV/div. to 5V/div.); DC to 5MHz (-3dB) (1mV/div. to 2mV/div.); DC to 20MHz (-3dB) (5mV/div. to 5V/div.); DC to 5MHz (-3db) (1mV/div. to 2mV/div.) Vertical axis frequency response AC 10Hz to 40MHz (-3dB) (5mV/div. to 5V/div.); 10Hz to 5MHz(-3dB)(1mV/div. to 2mV/div.); 10Hz to 20MHz (-3db) (5mV/div. to 5V/div.); 10Hz to 5MHz (-3dB) (1mV/div. to 2mV/div.) Approx. 8.75ns (40MHz) (5mV/div. to 5V/div); Approx. 70ns (5MHz) (1mV/div to 2mV/div); Approx. 17.5ns(20MHz)(5mV/div. to 5V/div.); Approx. 70ns (5MHz) (1mV/div. to 2mV/div) Below -40dB (at 1kHz sine wave) Vertical axis polarity inversion Vertical axis maximum input voltage Horizontal axis operating modes Switch to X-Y on CH1 : Y-axis : CH2 : X-axis Horizontal axis input impedance Horizontal axis frequency response DC : DC to 500kHz (-3db) /AC : 10Hz to 500kHz (-3db) Horizontal axis X-Y phase difference 0.2us/div. to 0.5s/div. +3%; 1-2-5 steps, 20 ranges, and fine adjustment; 0.5us/div. to 0.5s/div. +3% (0.2us/div.:UNCAL) Sweep magnified sweep (x10MAG) x10, +5%; x10, +5% (0.2us/div.:UNCAL) +3%(x10MAG : +5%); +3% (0.2us/div:UNCAL) (x10MAG:+5%, 20ns/div.: UNCAL) AUTO, NORM, FIX, TV-F and TV-L External triggering input impedance External trigger maximum input voltage 1V p-p+3% (Square wave, 1kHz, positive polarity) Intensity modulation: Input voltage TTL level (dark for positive voltage) Intensity modulation: Input voltage TTL level (dark for positive voltage) Intensity modulation input impedance Intensity modulation frequency response Intensity modulation maximum input voltage CHI Signal output output voltage Approx. 50mV/div. (loaded 50Q) CHI Signal output output impedance CHI Signal output frequency response 100hZ to 20MHz (within +3dB, loaded 50Q); 100Hz to 10MHz (within +3db loaded 50Q) Enables trace rotation adjustment from front panel 10 degreeC to 35 degree C, 85% or less (no condensation) 0 degree C to 40 degree C, 85% or less (temperature/humidity for operation) 100/120/220/230V AC +10% (250V AC maximum), 50/60Hz Instruction manual (1) /Probe (PC-54)(2) / Power cable (1) GOODS: ALL our items are FACTORY NEW (Kenwood cs-4125A 20 mhz oscilloscope is the responsibility of Nola Cross) |
Nola.cross@cedar--rapids.com (Nola Cross)
for more information.